John Deere 544J User Manual download pdf (Page 32)

Net engine power is with standard equipment including air

cleaner, exhaust system, alternator, and cooling fan, at standard

conditions per SAE J1349 and DIN 70 020, using No. 2-D fuel at

35 API gravity. No derating is required up to 5,000-ft. (1525 m)

altitude for the 444J and the 544J and up to 10,000-ft. (3050 m)

altitude for the 624J. Gross power is without cooling fan.

Specifications and design subject to change without notice. Wherever applicable, specifications are in accordance with ISO standards.

Except where otherwise noted, these specifications are based on units with standard equipment, ROPS cab, one optional rear counter-

weight, rear cast bumper/counterweight, 20.5R25 tires, full fuel tank, and 175-lb. (79 kg) operator.

DKAJULDR Litho in U.S.A. (06-10)

444 544 624

Engine

●●●

Certified to EPA Tier 2 emissions

●●● Wet sleeve cylinder liners

●●● Electronically controlled fuel system

●●● Automatic derating when system temperatures

exceeded

●● Monitor-selected high-altitude compensation

●●● Under-hood muffler with large exhaust stack

●●● Under-hood dual-element air cleaner with restriction

sensor in cab monitor

●●● Underhood, pre-screened air intake

●●● Fuel filter/water separator

●●● Heavy-duty steel fuel tank guard

●●● 500-hour full-flow spin-on oil filter

●●● Polyvee drive belt with automatic tensioner

● Automatic glow plugs

▲▲ Ether start aid (required for cold starting down to

–13°F [–25°C])

▲▲ Intake air heater (required for cold starting down to

0°F [–18°C])

▲▲▲ 110-volt engine coolant heater (required for cold

starting below –13°F [–25°C])

▲▲▲ Centrifugal engine air pre-cleaner

▲▲▲ Chrome exhaust stack

▲▲▲ Environmentally friendly engine oil drain

▲▲▲ Special-application trash screens, axle seal

guards, etc.*

Cooling

●●●

Heavy-duty trash-resistant high-ambient cooling

package

●●● Two-side access to all coolers

●●● Cooling system isolated from engine compartment

●●● Proportionally controlled (cool-on-demand), hydrau-

lically driven, swing-out fan

●●● Intercooler (air/air – 6.5 fins per in.)

●●● Transmission oil cooler (oil/air – 6.5 fins per in.)

●●● Hydraulic oil cooler (oil/air – 6.5 fins per in.)

●●● Engine radiator (7.5 fins per in.)

●●● Integral engine oil cooler

●●● Coolant recovery tank

●●● Fan guard

▲▲▲ Axle coolers (6.5 fins per in.)

▲▲▲ Reversing fan drive — auto control with manual

override

▲▲▲ Harsh-environment coolers for corrosive environments

Powertrain

●●●

ZF torque-converter powershift transmission — 4F/3R

●●● Electronically controlled, adaptive, load- and speed-

dependent shift modulation

●●● Clutch calibration engaged from cab monitor

●●● Clutch cutoff — thresholds set from switch pad

●●● Auto-shift/manual-shift modes

●●● Gear kickdown button in hydraulic-control lever

●●● Integral transmission sight gauge/fill tube

●●● Spring-applied, hydraulically released, oil-cooled,

multi-disc park brake

●●● Lube-for-life U-joints

● Heavy-duty mid-board planetary final drives

●● Heavy-duty inboard planetary final drives

●●● Front axle with hydraulic locking differential

▲▲▲ Front and rear axle with open differential*

▲▲ Front-axle disconnect

▲▲▲ Remote-axle breathers

Hydraulic System

●●●

Pressure-compensating load-sensing hydraulic system

●●● In-cab adjustable automatic bucket positioner

●●● In-cab adjustable automatic boom height kickout

control

●●● In-cab adjustable automatic boom return-to-carry

control

444 544 624

Hydraulic System

(continued)

●●● Reservoir sight gauge

●●● Spin-on hydraulic filters, vertical mounting

●●● Hydraulic lever lockout

●●● Two-function hydraulic valve with single-lever control

▲▲▲ Two-function hydraulic valve with two-lever fingertip

controls and adjustable wristrest

▲▲▲ Three-function hydraulic valve with single-lever

control and auxiliary lever for third function

▲▲▲ Three-function hydraulic valve with two-lever finger-

tip controls, adjustable wristrest, and auxiliary lever

for third function

▲▲▲ Four-function hydraulic valve, with dual single-lever

controls

▲▲▲ Hydraulic conversion kits, two-to-three- and three-

to-four-function valves

▲▲▲ Ride control, programmable auto speed

▲▲▲ Hydraulic control system for quick-coupler locking pins

Electrical

●●●

24-volt electrical system

●●● Solid-state electrical power distribution system

●●● High-capacity batteries (2), 12 volt with 950 CCA,

200-min. rated reserve

●●● Master electrical disconnect switch

●●● Alternator, high capacity, 80 amps and 24 volts

▲▲▲ Alternator trash covers

●●● Lights (conform to SAE 99): Driving with guards /

Turn signals and flashers / Stop and taillights

●●● LED heavy-duty taillights and turn signals

●●● Work lights, front (4) and rear (2)

●●● Horn, with push button in center of steering wheel

(conforms to SAE J994, J1446)

●●● Reverse warning alarm (conforms to SAE J994, J1446)

●●● Computerized multifunction monitor

●●● Audible and visual warnings: Amber caution / Red

stop / Analog gauges: Engine coolant temperature,

transmission oil temperature, fuel level, hydraulic

oil temperature, engine oil pressure / Digital instru-

ments: Engine rpm, odometer, transmission gear

indicator, speedometer, hour meter / Operator warn-

ing lights: Check engine, engine oil pressure, engine

air filter restriction, battery voltage, transmission

filter restriction, brake pressure, hydraulic oil filter,

fasten seat belt, transmission fault, hydraulic oil

temperature

●●● Indicator lights: Park brake / Ride control / Turn signals

and warning flashers / Coupler pin disconnect / Engine

preheater / Secondary steering / Work lights

●●● Built-in diagnostics: Fault code retrieval

▲▲▲ AM/FM/WB stereo radio

▲▲▲ AM/FM/WB stereo radio with cassette

▲▲▲ AM/FM/WB stereo radio with CD

▲▲▲ 5-amp, 12-volt convertor with one power plug

▲▲▲ 10-amp, 12-volt convertor with two power plugs

●●● Cab wired for rotating beacon

▲▲▲ Electrical corrosion-prevention package

Operator’s Station

●●●

Canopy (conforms to SAE J1040 APR88): ROPS/FOPS /

Multiplane isolation mounted for noise/vibration

reduction / Optional canopy rear window glass, for

noise reduction

▲▲▲ Cab (conforms to SAE J1040 ARP88): ROPS/FOPS /

Heater/defroster / Multiplane isolation mounted for

noise/vibration reduction / Front and rear windshield

washers and intermittent wipers / Tinted safety glass

▲▲▲ Canopy rear window

▲▲▲ Air conditioning

●●● Seat belt, 3 in. (76 mm), with retractor

●●● Air-suspension seat, deluxe vinyl covered with deep

foam, high back, adjustable for weight-height, fore-

aft position, backrest tilt, and armrest angle

444 544 624

Operator’s Station

(continued)

▲▲▲ Air-suspension seat, deluxe cloth covered with deep

foam, high back, adjustable for weight-height, fore-

aft position, backrest tilt, and armrest angle

●●● Seat backrest extension

●●● Cup holder, personal cooler holder

▲▲▲ Sun visor for cab

●●● Storage compartment for operator’s manual and

other items

●●● Rubber floormat

●●● Tilt steering column

●●● Steering wheel, textured with spinner knob

●●● Rearview mirrors, outside (2) and inside (1) (conform

to SAE J985)

●●● Handholds and steps, ergonomically located and

slip resistant (conform to SAE J185)

Loader Linkage

●●●

Loader boom service locking bar (conforms to

SAE J38)

●●● Z-bar loader linkage

▲▲▲ Powerllel linkage for visibility and parallel-lift

▲▲▲ High-lift Z-bar loader linkage

Buckets and Attachments

▲▲▲

Full line of Deere hook-on buckets with selection of

bolt-on cutting edges and teeth-segmented bolt-on

cutting edges*

▲▲▲ Full line of Deere construction utility forks for couplers

▲▲▲ Worksite Pro

quick-coupler which accepts JRB-

pattern attachments

▲▲▲ Hi-vis coupler which accepts Euro-pattern attachments

▲▲▲ Bolt-on fork frame guard

▲▲▲ Hydraulic control system for quick-coupler locking

pins, includes all controls in the cab, lines, and valves

Tires

▲

17.5-25 L2

▲ 17.5-25 L3

▲ 17.5R25 L2

▲ 17.5R25 L3

▲▲▲ 20.5-25 L2

▲▲ 20.5-25 L3

▲▲▲ 20.5R25 L2

▲▲ 20.5R25 L3

▲ 550/65R25 L2

▲▲ 600/65R25 L3

▲ 23.1-26 LS-2 Logger

▲ 28L-26 LS-2 Logger

▲ Single-piece rims

●●● Multi-piece rims

▲▲▲ Less wheels and tires

▲▲▲ 8-degree rear axle stops for extra-large tires and chains

Other

▲▲▲

Sound-suppression package

●●● Fenders, front

▲▲▲ Fenders, full-coverage front

▲▲▲ Fenders, full-coverage front and rear

▲▲▲ Close-mounted steps

●●● Articulation locking bar (conforms to SAE J276)

●●● Vandal protection, includes lockable engine enclosure

and fuel fill

●●● Counterweight, built-in

●●● Front and rear tie-down points

●●● Drawbar, with locking pin

▲▲▲ Rear cast bumper/counterweight with integral drawbar

▲▲▲ Transmission side frame guards

▲▲▲ Bottom guards, front frame and transmission

▲▲▲ Lift eyes

▲▲▲ Fire extinguisher

▲▲▲ License plate bracket and light

▲▲▲ Secondary steering

▲▲▲ Loadrite

weighing system

444J / 544J / 624J LOADERS

Key: ● Standard equipment ▲ Optional equipment *See your John Deere dealer for further information.

Vertis QCA

1300 19th Street, Suite 200

East Moline, IL 61244

Cyan

Magenta

Yell ow Black

DKAJULDR Page 32

DKAJULDR_SPECS 10/24/06 10:47 AM Page 32

1 2 ... 27 28 29 30 31 32

Comments to this Manuals

No comments

John Deere 544J User Manual Page 32

Comments to this Manuals

Related products and manuals for Tractor John Deere 544J